Protect your antenna base and maintain a clean seal with this antenna bezel gasket, designed specifically for 1963-1982 Chevrolet Corvette models. This factory-correct rubber gasket provides a snug fit around the antenna bezel, preventing…
This Corvette reproduction antenna nut has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
Protect your antenna base and maintain a clean seal with this rubber antenna bezel gasket, designed for 1955-1991 GM cars and trucks. This factory-correct gasket provides a snug fit around the antenna bezel, preventing moisture and debris…
Reproduction Of Original Round 30 Non-Retractable AM/FM. This Chevrolet reproduction antenna mast has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and…
Tapered mast as original (.100 at ball; .185 at mast).
Has correct .305 size ball.
This stainless steel antenna mast measures 31 1/2 inches overall length, with a thread size of 1/4 inch x 20.
…
Correct Reproduction
Attaches To Fender Hole Where Antenna Comes Through
Molded Plastic As Original
For Manual Antenna Only
Will Not Work For Power Antenna
Replaces GM Number 12337870
The antenna bezel supports…
Stock Replacement Fits 1969-75 Front Fits 1969 Rear This stock replacement antenna bezel nut is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit, finish and function…
Stock Replacement For Use With Antenna In Windshield Style El Camino's This stock replacement antenna lead wire is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit…
•Brand New
•Antenna delete block off plate for use on any 1979-1993 Ford Mustang
•Makes the Mustang look more like the Cobra R and eliminates the antenna
•Mounts on the passenger side fender at the antenna base
•Features four…
Reproduction Of Original Fits 1967-68 Rear Fits 1969-72 Front Replaces GM# 3897333 This Camaro reproduction front/rear antenna bezel has been manufactured to original factory specifications using today's modern manufacturing techniques…
Reproduction Of Original Used On Front Fender Antenna Don't forget to give your 1967-68 Camaro that finished look and replace that corroded antenna nut. A simple install but makes a big difference in your Camaro appearance.
…
Reproduction Of Original Fits 1965-69 Front Fits 1965-67 Rear Replaces GM# 3863499 This Chevelle reproduction antenna mast nut has been manufactured to original factory specifications using today's modern manufacturing techniques. You will…
This die cast, chrome plated spacer is angled.
The short side is 1/4 inch tall.
The tall side is 7/16.
O.D. = 1 5/16
I.D. = 3/4
There is a flange at the bottom which fits/snaps into gasket 162039
There is also a locator pin…
Correct reproduction zinc diecast chrome plated antenna nut used on all 65-68 Corvettes.
This antenna nut cap has the correct flats on the side of the nut and stepped lower edge where the nut mounts on top of the antenna bezel.
Hole…
Stock Replacement For Use With Antenna In Windshield Installs On The Upper Cowl Panel Correct Stamped Steel Ends 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979 Nova's are great to restore and fun to drive, the only thing better…
Reproduction Of Original Fits 1965-69 Front Fits 1965-68 Rear Replaces GM# 3863499 This Chevrolet reproduction front antenna mast nut has been manufactured to original factory specifications using today's modern manufacturing techniques…
This bronze antenna grounding plate, often referred to as a bezel or ring, mounts on the underside of the fender where the antenna protrudes through and acts to provide a secure ground to the body of the vehicle. Officially Licensed GM…